For completeness, we cannot say for sure if we even exist. The universe could very well just be an imagination and nothing really matters, including the laws of physics and our understanding of magnets.

Swiss here, Blick is known for low quality news. This “news” is only a claim from some unknown party. Very likely inaccurate or even plain wrong.

Also, it doesn’t feature a serial port. This phone is almost useless. /s

Yep… Max’s dominance seems to be a side effect of the new regulations for closer racing, IMO. The new regulations favor Max because he is so consistent and fast while still having a bit of a margin, combined with a now very reliable car, and a good portion of luck as well. I still think it’s more interesting to watch than the previous years. Max is, while more consistently in front, still closer to the pack than Hamilton in his dominant years.

I’d also lay a lot of the “problems” of the sport are also due to the attitude of the fans praising the winner in an “all or nothing”-fashion instead of focusing on the battles for 2nd-10th as well. F1 already did try a lot to change this, IMO (DotD, fastest Lap, new Regs, TV-directing)

Are you serious? Instead of doubling down on your ignorancy by asking rhetorical questions you could also try to inform yourself. The answer to your question is in OP’s post:

The children in these photos/videos can’t make pornography, they’re sexually abused into making this material. CP insinuates that it’s legitimate porn with children. CSAM, on the other hand, calls it what it is: sexual abuse of children.

Well I didn’t say it fixes the problem. I’m just saying you’re ignoring it. By ignoring the issue, you’re empowering the issue. Which is definitely worse than not doing anything. So your opinion is wrong and ill-educated.

Just because you aren’t affected doesn’t mean it is no problem. This isn’t needlessly pedantic, it just shows your ignorance and idiocy.

I have printed some food safe prints for a friend couple of times now. Nozzle is stainless steel, Filament is natural HIPS. Stainless & HIPS are both food safe materials (if not mixed with color pigments). After the print, you need a clean surface. HIPS can be smoothed in an Acetone-Bath. Simply put it in for 10-15 min and you’ll have a glossy finish.

HIPS is very easy to print in an enclosure and the resulting product is fairly stiff and durable. It’s also temp resistant up to 90-100°C. So it’s dishwasher safe.

Do not inhale acetone vapor, wear respiratory masks that filter out voc like acetone vapor.

I agree. One thing I’d like to add: There are also low thermal mass floor heating systems available nowadays (usually dry, built on top of a layer of Insulation). These aren’t that slow to react. But of course, these bring not only advantages but also drawbacks.

While being the cheapest, AC is also the type of heating with the least amount of comfort, while the most expensive solution, underfloor or wall heating is the best comfort. Radiant heat is much less intrusive than blowing air around violently.

You’re also wrong. Mainly, It has to do with the thermal capacity/mass of the building and not with differences in insulation values.

There are pros and cons for all building types.

Wearing a gun may give you some protection, but it also brings you a false sense of security and introduces countless new risks while negleting the source of the issue. If you’re actually living somewhere, where it’s “normal” to wear guns it’s a far better idea to just relocate. But then, many folks are just scared and don’t actually gain any increased safety from wearing a gun.

The label “nazi” just makes it easier to point fingers at them. It’s much more true that assholes, racists and fascists are simply everywhere. In every country and every society. We as a society need to do our job and fight for our rights, fight against the uprise of organized egoism.

There are recent examples, where we failed. f.e. russia, afghanistan the list goes on…

Aurora Store with microG exists though.

I was once at the exact same point where you are now. Marlin+octoprint really is good enough for most cases once you’re up and running.

I pulled the trigger for klipper a couple of years ago and honestly never looked back. Mainsail is just so much more refined and usable than octoprint. Tuning Firmware Settings in klipper is so much simpler than marlin, it’s just a breeze.

Combined with modern controller board (f.e. mks skipr), modern drivers like TMC2209, sensorless homing, Canbus-toolhead, resonance measuring, mmmh… chef’s kiss ;)